Contents
Our quick picksHow we chose1. Low Height Racking2. Shelving 875KG Single Shelving Unit, 1803. Racking 2100mm Low Height Racking4. Racking 2100mm Low Height Racking, 2100m5. Rhino Racking 200kg Black Single Shelvin6. Rhino Racking Black Low Height Racking7. Panana Steel Silver Low Height Racking8. Garage Low Height RackingMeasure your Custom before you buyHeight and depth on an H1 roofFixing points and floor kitsWeight and payloadL2 and Double Cab layoutsFAQsThe Transit Custom is the van most UK trades end up in, so it has more racking made for it than almost anything else on the road. That is good news for choice and bad news for decisions. Units that look identical online can differ by a few centimetres in depth, and those few centimetres decide whether a sheet of ply still slides in flat between the arches on a wet Monday. Plenty of owners only find that out after the bolts are in.
This guide covers racking for the L1, the longer L2 and the Double Cab. We look at height, depth, fixing points and weight, then set out the picks by job. The 2023-on Custom has a slightly lower load floor height than the 2012 model, so check which generation you drive before you order anything with a fixed height. A quick look at the plate on the B-pillar will tell you the wheelbase and roof height, and that is the detail sellers ask for first.
Our picks at a glance
- Low Height Racking: best overall, £32.99
- Shelving 875KG Single Shelving Unit, 180x90x40cm: best budget, £19.39
- Racking 2100mm Low Height Racking: best for the l2, £149.99
- Racking 2100mm Low Height Racking, 2100mm H x 900mm: best for the double cab, £119.99
- Rhino Racking 200kg Black Single Shelving Unit: best angled shelving, £34.99
- Rhino Racking Black Low Height Racking: best for small parts, £260.99
- Panana Steel Silver Low Height Racking: best lightweight option, £19.99
- Garage Low Height Racking: best full side kit, £26.99
How we chose
We started with the internal sizes of each Custom body and kept to units listed for that van or sized to suit an H1 roof, which means about 1,000 mm tall. We favoured shelving no deeper than about 380 mm so the floor between the arches stays usable. We then looked at shelf adjustability, how the unit fixes to the floor and side, listed shelf loads and the reviews from people who fitted them. Nothing here was tested by us; the picks reflect what the listings and owner reviews describe.

1.Low Height Racking
This is the one we would point most people to for overall. Specs worth noting: material Metal. 4,308 buyers rate it 4.1 out of 5. £32.99, one of the cheaper options here. Have a look at the Low Height Racking for the full spec.
Compare it with the rest of our low height racking 1000mm.

2.Shelving 875KG Single Shelving Unit, 180x90x40cm
This is the one we would point most people to for budget. Specs worth noting: dimensions 180x90x40cm, max load 875KG, material Metal. 932 buyers rate it 4.4 out of 5. £19.39, one of the cheaper options here. Have a look at the Shelving 875KG Single Shelving Unit, 180x90x40cm for the full spec.
Compare it with the rest of our low height racking 1000mm.

3.Racking 2100mm Low Height Racking
Racking 2100mm Low Height Racking is our pick for for the l2. Specs worth noting: size 2100mm. It averages 4.4 stars from 1,310 reviews. £149.99, so you pay a bit more for the spec. You can see the full specs and photos on the Racking 2100mm Low Height Racking page.
Compare it with the rest of our low height racking 1000mm.

4.Racking 2100mm Low Height Racking, 2100mm H x 900mm
If you want something for the double cab, start here. Specs worth noting: size 2100mm. It averages 4.4 stars from 1,310 reviews. £119.99, so you pay a bit more for the spec. Full details, sizes and photos are on the Racking 2100mm Low Height Racking, 2100mm H x 900mm page.
There are other options in our low height racking 1000mm range too.

5.Rhino Racking 200kg Black Single Shelving Unit
This is the one we would point most people to for angled shelving. Specs worth noting: dimensions 150x75x30cm, max load 200kg, colour Black. 1,250 buyers rate it 4.4 out of 5. £34.99, one of the cheaper options here. Have a look at the Rhino Racking 200kg Black Single Shelving Unit for the full spec.
Black Storage Shelves
150x75x30cm
Compare it with the rest of our low height racking 1000mm.

6.Rhino Racking Black Low Height Racking
If you want something for small parts, start here. Specs worth noting: dimensions 150x75x30cm, colour Black. It averages 4.4 stars from 1,250 reviews. £260.99, so you pay a bit more for the spec. Full details, sizes and photos are on the Rhino Racking Black Low Height Racking page.
5 Tier Heavy-Duty Industrial Storage Shelves
Black
Compare it with the rest of our low height racking 1000mm.

7.Panana Steel Silver Low Height Racking
Panana Steel Silver Low Height Racking is our pick for lightweight option. Specs worth noting: dimensions 180x90x40cm, material Steel, colour Silver. 1,184 buyers rate it 4.4 out of 5. £19.99, one of the cheaper options here. You can see the full specs and photos on the Panana Steel Silver Low Height Racking page.
180x90x40cm
If it is not quite right, we stock plenty more low height racking 1000mm.

8.Garage Low Height Racking
This is the one we would point most people to for full side kit. Specs worth noting: material Metal. It averages 4.2 stars from 1,448 reviews. £26.99, one of the cheaper options here. Have a look at the Garage Low Height Racking for the full spec.
There are other options in our low height racking 1000mm range too.
Prefer to browse everything? Our full ranges of low height racking 1000mm have more sizes, finishes and price points than we could fit here.
Measure your Custom before you buy
A 2023-on Custom L1 gives roughly 2.6 metres of floor length and about 1.27 metres of height, with close to 1.39 metres between the wheel arches. The L2 adds around 370 mm of length. Those are rough numbers, so run a tape along your own van, because ply lining, a floor kit and a bulkhead each take a slice. Write down the length from bulkhead to the rear door seal, the height at the side wall and the gap between the arches. Those three figures will rule out most of the wrong units straight away.
If you drive a 2012 to 2023 Custom, the roof sits a little higher inside, so some older racking is taller than the new body allows. Listings often say which years a kit suits. If a seller only says Transit Custom without dates, ask before buying, as returning a heavy steel unit is slow and usually costs you the carriage. It also helps to note where the side door opening starts and stops, since a unit that juts into it slows down every single drop you make.
Height and depth on an H1 roof
Almost every Custom is an H1, and the usual rule is a unit of around 1,000 mm. That leaves room for the roof curve and lets you reach the top shelf without climbing in. Go much taller and the top shelf hits the roof bow or sits too deep under it to load from the side door. Lots of people also forget the trims. A plastic side trim or a factory load light can stop a unit sitting flush, so check those spots before you settle on a design.
Depth matters more than people expect. Shelving of about 300 mm keeps the centre of the van open, while 380 mm units hold bigger cases but narrow the gap. If you carry 2,440 by 1,220 mm sheets, plan for units on one side only or a shallow unit opposite a deeper one. A layout drawn on paper first saves a lot of swearing. Some owners split the difference with a 300 mm unit by the door and a deeper section further forward, where sheets do not need to pass.
Fixing points and floor kits
The Custom has threaded fixing points along the lower sides and in the floor area. Good kits use these with brackets and spreader plates rather than self-tappers through the panel. If your van has a ply floor, you may need longer bolts or packers, so check what comes in the box. Kits made for the Custom usually list the bolt sizes and the points they use. If a kit only offers wood screws or self-drilling screws, treat that as a warning sign and look at something better made.
A rack that moves under braking is a hazard as well as a nuisance. Look for units with both floor feet and a top or side bracket that ties into the body. Retighten everything after the first week, as bolts can settle once the floor ply has been compressed. If you are fitting it yourself, use a torque wrench where the instructions give a figure. Overtightening into a thin panel can strip the thread, and a loose fixing will rattle within days.
Weight and payload
The Custom has a decent payload, but a full steel kit can use more of it than you might think. A double steel unit with drawers can weigh well over 60 kg before you add tools. Aluminium units cut that, though they usually cost more. Steel shelving is also heavier to lift into place, so have a second pair of hands on fitting day. Carry the unit in empty, fix it, and only then load the shelves.
Add up the weight of the racking, your tools, stock and any roof rack, then compare it with the payload on your V5 or the plate on the door pillar. Running close to the limit hurts fuel economy and wears brakes and tyres faster, and an overloaded van is an offence if you are stopped. A trip to a public weighbridge with the van loaded as normal costs little and gives you a real figure instead of a guess. Many trades are surprised by the result.
L2 and Double Cab layouts
The L2 lets you run two 1,000 mm wide units along one side with room left for a narrow unit or case rail by the door. Many owners put shelving on the nearside, where the sliding door gives easy access, and keep the offside clear for long lengths. A good spot by the rear doors for a narrow unit is often where bulky consumables such as sealant boxes or fixings go, as you can reach them without climbing in.
The Double Cab gives about 1.9 metres of load floor behind a second row, so a single unit on one side is often the limit. Shallow units and wall-mounted case rails make better use of this short space than full shelving. Check the rear seat frame and partition position before choosing a unit length. Double Cab owners often lean on roof bars and a pipe tube to carry the long items that will no longer fit inside, which frees the short floor for cases.
Frequently asked questions
Does racking from an older Transit Custom fit the new model?
Not always. The 2023-on Custom has a different load height and body shape from the 2012 model, so a unit sized for one can be too tall or the brackets may not line up. Check the years in the listing and measure your own van before ordering.
What height racking suits a Transit Custom?
Most owners choose racking about 1,000 mm tall for an H1 roof. It clears the roof curve, lets you reach the top shelf from the side door and leaves room for brackets. Higher roof Customs are rare, so taller units are seldom a good fit.
Can I still carry sheets of ply with racking fitted?
Usually yes, if you keep shelving shallow. With units around 300 mm deep on one side, an 1,220 mm wide sheet can often lie flat between the arches. Measure the gap on your van with lining fitted, as every millimetre counts.
Do I need to drill the van to fit racking?
Good Custom kits use the existing fixing points in the floor and lower sides, so drilling is often not needed. Some kits add top brackets that fix through the ply lining. Avoid drilling into the roof or near wiring, and follow the fitting guide.
How much does racking for a Transit Custom cost?
Boxed single units start around £100 to £150, mid-range kits for one side run from about £300 to £600, and fitted premium systems can cost £1,500 or more. Price depends on steel or aluminium, drawers and whether you fit it yourself.